Free · no signup to try · nothing to install

Bridge Designer

Bridge Designer puts a student in the job of a highway engineer: design a steel truss bridge across a river valley that carries its own weight and a truck, for as little money as possible. It opens on a 20 meter Warren truss that passes its load test at $287,807.17. Press the load test and the truck drives across in 3D, every member glowing red where it is squeezed and blue where it is pulled. Then make it cheaper and test it again. Free, in the browser, no account needed to try it.

Press the load test button in the toolbar, just right of the Design bridge button (or Test, then Load test), and watch the truck cross. Press Design bridge to come back. To make the bridge cheaper, press Select all, then Downsize selected members, and test again. The cost is at the top. It needs a mouse or trackpad and a screen at least 1280 by 720.

Open it full screen

Using this with a class? Make a free class and add your students yourself: each gets a username and password, with no email or Google account needed. Or give them one join code. Using Google Classroom? Post the link there; with a free class, the link also puts each student in your class, so you see their work. mytekDev is also available from the Google Workspace Marketplace, so your school's Google admin can install it for everyone.A first lesson: Everyone starts from the same Warren truss at $287,807.17. The goal is the cheapest bridge that still passes the load test, and the winner has to point at the member that would fail first and say why.

Set up a free class Share to Google Classroom
Put this on your class site

Students can use Bridge Designer right on your page, with no account. What they make stays on that page; to keep their work, they make a free account.

Google Sites: Insert, then Embed, then By URL, and paste this address.

https://mytekdev.com/try/bridgedesigner?embed=1

Canvas, a blog, or any page that takes HTML: paste this code where you edit the page as HTML.

<iframe src="https://mytekdev.com/try/bridgedesigner?embed=1" width="100%" height="640" style="border:0" allow="fullscreen" title="Bridge Designer demo from mytekDev"></iframe>

What a student actually does

They press the load test and watch a truck cross the bridge in a 3D river valley. The top of the truss glows red, the bottom glows blue, and the status sign turns green: it passed. Back on the drafting board the member table has filled in, one row per member, with how hard each one is squeezed or pulled compared with what it can take. Most of the numbers are small, which is the point. This bridge is stronger than it needs to be, and every extra kilogram of steel is on the bill.

So they make it cheaper. They select members and downsize them, swap a solid bar for a hollow tube, or try a different steel, then test again and watch the cost. Sometimes a member turns bright red and the bridge collapses, and they find it in the table and size it back up. From there they can start a new bridge from scratch: the setup wizard picks the deck height, abutments and piers, offers Pratt, Howe and Warren truss templates to trace, and leaves them to place joints and members on a grid. Each round of changes is numbered as an iteration, and the arrows on the toolbar step back to an earlier one while they work. Only the latest design is saved.

The same truss after every member was downsized from 160 mm to 120 mm and the load test was run again. The cost at the top reads $226,772.79 and the status shows a green passing sign. The members are highlighted blue and numbered 1 to 19. The member table now fills in compression and tension columns: the top chord members 7 to 10 read 0.55, 0.81, 0.79 and 0.51 in compression, the end posts 6 and 11 read 0.73 and 0.69, and the bottom chord members 1 to 5 read between 0.12 and 0.37 in tension.

Four presses of Downsize took every member from 160 mm to 120 mm and the cost from $287,807.17 to $226,772.79, and the bridge still passes. The table says why it is not safe to keep going everywhere: each number is the force in the member divided by its strength, and a member fails above 1.00. The top chord is already at 0.81 in compression, while the bottom chord carries at most 0.37 in tension, so the next savings come from the bottom.

What they are learning while they build

Nothing here is presented as a lesson. This is what the activity is made of.

What the student doesWhat it is
Watches the top chord glow red and the bottom glow blue Compression and tension. Under load, some members are pushed together and others are pulled apart. In this truss the top is squeezed and the bottom is stretched.
Reads 0.81 in the member table Force against strength. A member is safe while the force in it is less than its strength. The table shows the ratio, so 1.00 is the edge.
Builds the bridge out of triangles Why trusses use triangles. A triangle cannot change shape without changing the length of a side, so a frame of triangles holds its shape under a load.
Shrinks members until one fails, then backs off Design tradeoffs. Cheaper and stronger pull in opposite directions. The job is to find the cheapest design that still meets the requirement.
Notices long members need to be bigger when they are squeezed Buckling and slenderness. A member is always weaker pushed than pulled. A long, slender one pushed from both ends bends sideways, so its strength in compression can be far below its strength in tension.
Picks between carbon steel, two stronger steels, bars and tubes Materials and cross sections. A stronger steel costs more per kilogram. A hollow tube costs more per kilogram than a solid bar but resists buckling better for the same weight, so it often pays off in compression.
Tests, changes one thing, and tests again The engineering design process. Each test is an iteration. Changing one thing at a time is how you know which change made the difference.

How to tell whether it landed

Ask, and let them show you. A student who has understood it can answer these without help.

The last one is the real test. A student who predicts that a taller truss lowers the chord forces, then runs it to check, is reasoning about the structure rather than pressing Downsize until something breaks.

Use it in your subject

Not a technology class? Then the app is how students show what they learned in your unit. More projects for every subject.

Engineering and technology

Run the cheapest-bridge challenge on the starter, then have each student write a short design memo: what they changed, what it saved, and which member limits the next saving.

Physical science

Use the load test colors to sort members into compression and tension, then build the same truss from craft sticks and press on it to feel which parts push and which pull.

Math

Record cost and the largest force-to-strength ratio after each iteration and graph one against the other. Where does saving money start to cost safety?

Practical notes

For co-ops, microschools, and classrooms

Hand everyone the same bridge and the same goal: the lowest cost that still passes the load test. The test is the judge, so nobody needs a teacher to say whether a bridge works, and the member table gives every student evidence for why it did or did not.

Set up a free classroom

Common questions

Is it free?

Yes. It runs in your browser and there is no paid tier. A free account adds saving, but nothing on this page is behind a paywall.

Is this the West Point Bridge Designer?

It comes from the same family. Steve Ressler wrote the first Bridge Designer, which schools knew as the West Point Bridge Designer, and Gene Ressler later rewrote it and made it open source. Its newest version is Bridge Designer, Cloud Edition, which ASCE hosts and describes as the newest version of a free, open source application available since 2002. What runs here is a copy of that Cloud Edition source, by Steve and Gene Ressler and contributors, under the GNU GPL. We removed the ASCE name and logo and made bridges save to a student's account. It is not made, hosted or endorsed by West Point, ASCE or the authors, and the app's own About box says it is for educational use only.

Does my child need an account to try it?

No. The demo on this page is the whole app with the Warren truss loaded, and it keeps changes in the browser tab. Saving needs a free account.

Does it run on a Chromebook?

Yes, with a trackpad or mouse and a screen of at least 1280 by 720. It runs in Chrome, Edge, Firefox and Opera. It does not support Safari or touch-only tablets, and on a device it thinks is too small or touch-only it shows a warning first. Choosing Cancel lets it run anyway.

Can students save their bridge as a file?

Save keeps the bridge in the student's account. Save As also downloads it as a .bdc file, the Bridge Designer file format, so it can be opened again later or handed in.

Can a bridge be 3D printed?

The app can export the bridge as OBJ files to 3D print, and its Help has instructions for printing and putting the pieces together.

Is a student's work public?

No. Bridges are private by default. A student can choose to share one. In a class the teacher can see students' projects.

What subject can I log this as?

Most families log it as engineering or physical science: forces, compression and tension, and the design process. The cost and force-to-strength numbers make it count toward math too.

Still have a question? Ask us, and a person will write back.

Where to go next

Start with Bridge Designer

Trying it costs nothing and takes about five minutes. An account is what makes the work last.

Bridge Designer is one of the making apps on the platform. Every detail on this page was read from the app itself with the Warren truss starter. It is a place to make things, not a course, and it is not a substitute for a teacher: it is at its best when an adult asks the questions above and takes the answers seriously.
Bridge Designer is by Steve Ressler and Gene Ressler, with Jason Brett, Bill Carey and Mike Maffei, used under the GNU GPL v3. This is a modified copy: the ASCE branding is removed and bridges save to the student's account. Source.
Page last reviewed November 2026.
Google, Google Classroom and Chromebook are trademarks of Google LLC.