CircuitSim
An LED with no resistor in front of it burns out, and most students have never seen why. CircuitSim opens on a small circuit: a 9 volt battery, a switch, a 330 ohm resistor and a red LED. Students press Simulate, close the switch, and the LED lights while the Ohm's Law panel shows the voltage, the current, the resistance and the power. Then they pick smaller resistors until the current climbs past what the LED can take and it burns out. Free, in the browser, no account needed to try it.
Using this with a class? Make a free class and add your students yourself: each gets a username and password, with no email or Google account needed. Or give them one join code. Using Google Classroom? Post the link there; with a free class, the link also puts each student in your class, so you see their work. mytekDev is also available from the Google Workspace Marketplace, so your school's Google admin can install it for everyone.A first lesson: Everyone starts from the same circuit and finds the smallest resistor in the list that keeps the LED lit, then explains with V = I × R why the next one down burns it out.
Set up a free class Share to Google ClassroomWhat a student actually does
They press Simulate and nothing lights: the switch is open, so there is no complete path. They double-click the switch, it turns to CLOSED, dots start moving along the wires and the LED glows. The Ohm's Law panel reads 9.0V = 20.9mA × 430.1Ω, and Circuit Insights calls 20.9 milliamps ideal for an LED. Then they click the resistor and pick values from the Resistance list under Properties. At 470 ohms the current drops to 15.8 and the LED dims. At 220 it rises to 28.1, and a warning says the LED is near its 30 milliamp limit. At 100 it burns out. Stop, or pressing Simulate again, clears the damage.
From there they can build their own. The parts are a battery (3, 6 or 9 volts), resistors from 10 ohms to 100 kilohms, LEDs in five colors, a diode, a switch and a ground. A part is dragged in from the list on the left, and a wire is drawn by clicking one part's yellow dot and then another's. Clicking a part shows its own voltage, current and power. A Robotics list adds a Raspberry Pi, a motor driver, a battery pack and a DC motor, with a Robot Wiring checklist that ticks off each connection. With every connection made, the simulation running and the Pi's pin set high, the motor turns. Circuits save to the student's account.
The resistor set to 100 ohms. The current jumps to 45 milliamps, past the 30 the LED can take, and it burns out. With 220 ohms it carried 28.1 and stayed lit. In this model the LED counts as about 100 ohms, so the total resistance sets the current: 9 volts across 200 ohms is 45 milliamps.
What they are learning while they play
Nothing here is presented as a lesson. This is what the activity is made of.
| What the student does | What it is |
|---|---|
| Presses Simulate with the switch open and nothing happens | Open and closed circuits. Current flows only around a complete path. An open switch breaks the path, so nothing flows however strong the battery is. |
| Reads 9.0V = 20.9mA × 430.1Ω in the Ohm's Law panel | Ohm's law. Voltage equals current times resistance. Knowing any two gives the third, so 9 volts across 430 ohms has to mean about 21 milliamps. |
| Adds the resistor's 330 ohms to the LED's 100 | Resistance in series. Parts in a single loop add up, and the same current passes through every one of them. |
| Picks a bigger resistor and watches the current fall | Current and resistance. With the voltage fixed, more resistance means less current. Half the current needs twice the total resistance. |
| Burns out the LED with a 100 ohm resistor | Current limiting. An LED is made to carry a small current. The resistor in front of it holds the current down, which is why every LED in a real kit comes with one. |
| Reads the Power row as the current climbs | Electrical power. Power is voltage times current, measured in watts. It is the rate a part turns electricity into light or heat, and too much of it destroys the part. |
| Wires a Raspberry Pi to a motor through a driver board | Driving a motor. A computer's pins send signals, not the power a motor needs. A driver board takes the signal and switches the battery's power to the motor. |
How to tell whether it landed
Ask, and let them show you. A student who has understood it can answer these without help.
- You pressed Simulate and nothing lit. What did the switch have to do with it?
- Before you change it: will a bigger resistor make the current go up or down?
- Which is the smallest resistor in the list that keeps the LED lit, and what current did it carry?
- Use V = I × R to explain why the next one down burned the LED out.
- A friend wires an LED straight to a battery. What would you tell them, and why?
Use it in your subject
Not a technology class? Then the app is how students show what they learned in your unit. More projects for every subject.
Physical science
Predict the current for each resistor with V = I × R before running it, then check the prediction in the Ohm's Law panel and explain any difference.
Math
Record the current for five resistor values in a table and graph current against resistance. The curve shows an inverse relationship, not a straight line.
Engineering and CTE
Design to a rating: the LED wants about 20 milliamps and burns out above 30. Pick the battery and the resistor that keep it inside that range, and justify the choice.
Practical notes
- AgesGrades 6 through 12. Younger students close the switch, change the resistor and describe what happens; older ones predict every current with V = I × R before they run it.
- TimeA couple of minutes to a lit LED. Finding the smallest safe resistor and explaining it takes ten to twenty minutes, and building a circuit from scratch most of a period.
- EquipmentA computer or Chromebook with a keyboard and a modern browser. Deleting a part (Delete) and turning one (R) are keyboard keys with no on-screen button, so a touch-only tablet cannot do either. It does not open on a phone. Nothing to install.
- CostFree. The app has no paid tier.
- PrepAbout five minutes: close the switch and step the resistor down to 100 ohms yourself, so you know what the class will see.
- In a groupEveryone starts from the same circuit and the same question, so the class can compare answers and settle any disagreement by running it.
For co-ops, microschools, and classrooms
Hand everyone the same circuit and the same goal: the smallest resistor that keeps the LED alive. Each student finds it by trying, and then has to explain it with numbers from the panel, so the check is the student's own working rather than the teacher's say-so.
- Live voltage, current, resistance and power as the circuit runs.
- Parts burn out when they carry too much, and Stop resets them.
- Circuit Insights explains what the circuit is doing in plain words.
- No install, no per-seat license. Student work is private by default.
Common questions
Is it free?
Yes. It runs in your browser and there is no paid tier. A free account adds saving, but nothing on this page is behind a paywall.
Does my child need an account to try it?
No. The demo on this page is the whole app with the starting circuit loaded. Saving needs a free account.
How realistic is it?
It teaches the main idea correctly and simplifies the rest. It works out each path from the battery as resistances added in a line, and counts an LED as a fixed 100 ohms. For the 330 ohm starting circuit its answer is close to what a real red LED would draw, but with small resistors it shows less current than a real one. Parallel branches are not solved the way a real circuit shares current: each branch gets the full battery voltage. It does not check which way round an LED is wired, and it runs on direct current only. There are no capacitors, bulbs or meters.
Why does the LED burn out at 30 milliamps?
The app gives every LED a 20 milliamp rating and burns it out above 30, which is in the range of a typical small indicator LED. A real one has its limits printed on its data sheet.
What are the robotics parts for?
The Robotics list has a Raspberry Pi, a motor driver, a 4 AA battery pack and a DC motor. The Robot Wiring panel lists the connections a real build needs, ticks each one off as it is wired, and the motor turns when they are all made and the Pi's pin is set high. It is a wiring exercise: the motor and the driver are not part of the electrical calculation, and the Pi does not run code.
Does it work on a tablet or Chromebook?
On a Chromebook, yes. Parts can be placed, moved and wired by touch, and a double tap changes a part's value, but deleting and turning a part need the keyboard, so a tablet with no keyboard cannot do either. It does not open on a phone.
Is a student's work public?
No. Circuits are private by default. A student can choose to share one. In a class the teacher can see students' projects.
What subject can I log this as?
Most families log it as physical science: circuits, Ohm's law and power. The table of currents and the graph are math, and designing a circuit to stay inside a part's rating is engineering.
Still have a question? Ask us, and a person will write back.
Where to go next
Start with CircuitSim
Trying it costs nothing and takes about five minutes. An account is what makes the work last.
CircuitSim is one of the making apps on the platform. Every number on this page was read from the app itself with the starting circuit. It is a place to make things, not a course, and it is not a substitute for a teacher: it is at its best when an adult asks the questions above and takes the answers seriously.
Page last reviewed November 2026.
Google, Google Classroom and Chromebook are trademarks of Google LLC.